- Navigation
Results 1 to 10 of 10
Thread: center console
-
05-12-2009, 08:55 PM #1
center console
how does the center console come out on a 94 TRANS AM??????? i dont wanna break it... or ruin my transmission performance button
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
-
05-12-2009, 09:02 PM #2
What part of the console? Do you just need the center part out (around the shifter including the cup holder and ash tray) or the whole thing including the glove box.
2003 Mustang Cobra SVT: just an Eaton... 505/525
1996 Trans Am: 52mm Holley, LPP Longtubes, GMMG Catback, 3.73's, PCMforless tune. SOLD
1995 Trans Am: Borla Exhaust, K&N Air Intake, pacesetter headers. SOLD
-
05-12-2009, 09:06 PM #3
just the part where the shifter thingy is haha
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
-
05-12-2009, 09:22 PM #4
Put the car in Neutral and look on the back of the shifter (towards the front of the car) there is a little staple looking thing. Stick a straight head screwdriver through that and pull it out. The Shifter knob will come off then. The rest of it is just held on by clips, you will have to pull them out, but don't go ripping it off because as your doing it you will have to be unhooking your "Transmission Perform" wire. When pulling it off start from the front or back, I can't remember where I started but it's pretty simple to do.
2003 Mustang Cobra SVT: just an Eaton... 505/525
1996 Trans Am: 52mm Holley, LPP Longtubes, GMMG Catback, 3.73's, PCMforless tune. SOLD
1995 Trans Am: Borla Exhaust, K&N Air Intake, pacesetter headers. SOLD
-
05-12-2009, 09:30 PM #5
alright thanks you man!!!!!
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
-
05-12-2009, 09:50 PM #6
alright... so i went to take the shifter knob off and... that staple thing went in like 2 centimeters and now it wont move........... the knob wont come off either.................
!!!!
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
-
05-12-2009, 09:58 PM #7
Went in? You should be able to pull it out.
2003 Mustang Cobra SVT: just an Eaton... 505/525
1996 Trans Am: 52mm Holley, LPP Longtubes, GMMG Catback, 3.73's, PCMforless tune. SOLD
1995 Trans Am: Borla Exhaust, K&N Air Intake, pacesetter headers. SOLD
-
05-12-2009, 10:31 PM #8
pull that staple thing out?
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
-
05-13-2009, 05:58 AM #9
Yeah, Pull it completely out. When you go to put it back in you will have to squeeze the ends of it together a little but it won't be too bad.
2003 Mustang Cobra SVT: just an Eaton... 505/525
1996 Trans Am: 52mm Holley, LPP Longtubes, GMMG Catback, 3.73's, PCMforless tune. SOLD
1995 Trans Am: Borla Exhaust, K&N Air Intake, pacesetter headers. SOLD
-
05-13-2009, 11:12 AM #10
ok the job is done
thanks
1994 T\A, BBK shorties,CAI, cutout, full exhaust,MSD wires, 160* t-stat, 3.73s, cc503-1.6rr's-lunati lifters-stock pushrods FTW
Reply With Quote

Bookmarks