Project Rainbow Unicorn 2013

I let Shownomercyz28 chime in with specifics, but basically he bought one of my used PT88 hotparts that i reworked for him, and will be sending him a complete kit. He will be running a 383ci (single plain intake, he can give details).

The kit consists of the following:

Precision T76GTS
1 5/8" headers (reworked BBK's)
2.5" crossover
3" up pipe
3" downpipe
JGS 50mm wastegate
JGS60mm BOV
31x12x4" A2A IC
3" cold side piping
RPS couplers and T-bolt clamps
oil lines

Hotside Mockup
http://i45.photobucket.com/albums/f9...0Kohler/13.jpg

http://i45.photobucket.com/albums/f9...0Kohler/12.jpg

http://i45.photobucket.com/albums/f9...20Kohler/3.jpg

http://i45.photobucket.com/albums/f9...20Kohler/2.jpg

http://i45.photobucket.com/albums/f9...20Kohler/9.jpg

http://i45.photobucket.com/albums/f9...20Kohler/6.jpg

http://i45.photobucket.com/albums/f9...20Kohler/4.jpg

Cold side Mockup
http://i45.photobucket.com/albums/f9...toCARW8DEX.jpg

http://i45.photobucket.com/albums/f9...toCA4X6U3I.jpg

http://i45.photobucket.com/albums/f9...toCAND4RXE.jpg

http://i45.photobucket.com/albums/f9...toCAAKG0D6.jpg

http://i45.photobucket.com/albums/f9...toCAAKG0D5.jpg

http://i45.photobucket.com/albums/f9...toCAAKG0D8.jpg

http://i45.photobucket.com/albums/f9...toCAAKG0D9.jpg

http://i45.photobucket.com/albums/f9...toCABWWO7P.jpg

Looks good and hoping the install goes smooth. I will be giving him a hand so nice to see everything should fit as it should :).

Oh and can you make sure to install something so this makes less than 709 rwhp?

Just keep it under 767 is what I say. Haha

Sent from my ADR6425LVW using Tapatalk

Quote:

---

Originally Posted by blackbirdws6

Oh and can you make sure to install something so this makes less than 709 rwhp?

---

I'll stuff a shop rag in one side of the crossover ;)

Unlike you two, it will not be a dyno queen, only goal is a low low 10 sec pass.

Quote:

---

Originally Posted by shownomercy

Unlike you two, it will not be a dyno queen, only goal is a low low 10 sec pass.

---

My car has been on the track already thank you very much. ;)

Sent from my ADR6425LVW using Tapatalk

Same. :)

Matt, any pics of the intake/TB setup?

To be honest Jon, you kinda jumped the gun on me, I am no where near getting ready to build this thing. lol

Its a modified single plane with an edelbrock low profile elbow though.

I have the engine in my garage now, next up is buying a transmission for the car.

Does anyone know if someone does the re-pinning of a 96 LT1 harness to a 24x setup?

Matt, you receive the intercooler yet?

Yea it actually made it to work on Friday but I was MIA that afternoon ;) So grabbed it this morning, looks good sitting on my desk at work

https://fbcdn-sphotos-a.akamaihd.net...29323076_n.jpg

Pardon the dirty car and missing elbow/throttle body

how did you bend the pipe? Was it pre bent stuff or did you use a pipe bender.

Quote:

---

Originally Posted by shownomercy

https://fbcdn-sphotos-a.akamaihd.net...29323076_n.jpg

Pardon the dirty car and missing elbow/throttle body

---

Nice!

Adam - I bend U bends (180 degrees) and cut the angles I need.

Hot side clears a 7qt canton pan, big relief and thought you would wanna know Jon.
https://fbcdn-sphotos-a.akamaihd.net...57958819_n.jpg

Pistons will be here some time before the end of the month.

I wish I could afford boost :(! Kit looks great!

Oh and what did you guys run at the track???????

The old stock bottom end with LE2s went 12.1 @116 and then trans started to go, and it was just running consistent mid 12s.

This time round I am shooting for bottom 10s

Quote:

---

Originally Posted by shownomercy

Hot side clears a 7qt canton pan, big relief and thought you would wanna know Jon.
https://fbcdn-sphotos-a.akamaihd.net...57958819_n.jpg

Pistons will be here some time before the end of the month.

---

Looks good... but test fit it with the K member too.

K member is a PA racing unit, so I have high hopes it will fit, really really don't wanna drag the stocker out of the basement lol

http://i176.photobucket.com/albums/w...s/IMG_1053.jpg

Awww yea

Hmmmm......do like.

Moar parts pRon

http://i176.photobucket.com/albums/w...s/IMG_1016.jpg

http://i176.photobucket.com/albums/w...s/IMG_1072.jpg

Looking good! I cant wait for my build to start.

So prob next month pending finances, I am gonna grab the EFI 24x hardware and a cam....

Right not I am stuck between a 224/224 .573/.565 114 or a 224/230 .573/.565 116 both would be XFI lobes.

Nice. Do like the 24x stuff. Their harness is a work of art.

I just repinned my stock harness, 12week backorder? No thanks lol

Whoring out pic cause I can.
http://i924.photobucket.com/albums/a...g?t=1348282042

Nice job there.

Danke, I will grab some more pics of machining on Monday, left it at work cause I gotta finish the o ring spot face.

http://i924.photobucket.com/albums/a...g?t=1353728170

i hope that pic is just a teaser and there are more to come!

looking good!

Quote:

---

Originally Posted by shownomercy

Unlike you two, it will not be a dyno queen, only goal is a low low 10 sec pass.

---

DAYUMMMMMMMM>..... lol



Seriously though... looks good!

Dis gonna be good.

http://i924.photobucket.com/albums/a...w/IMG_1511.jpg

So I realized that I do not have a downpipe for my wastegate, is it needed?

Put a duck call on there.

Quote:

---

Originally Posted by Mystery Bird

Put a duck call on there.

---

WIN! I love that vid.

For what it's worth I have about a 6" turn down on my wastegate and it's fine.

http://i924.photobucket.com/albums/a...g?t=1353988138

As far as meth placement... Jon threw a couple bungs right before the MAF/IAT, but their close, like within 4inchs, think its far enough?