Custom, New and used parts half price

Several new and used parts looking for a new owner. Nothing wrong with them, just running a different setup now. I wish I could buy the parts I need at half price but never works that way for me:).

Two "one of one" custom cams made by Comp cams special for me. These were designs for lobe profiles and ramp speeds that make them drive nice on the street while still making big power numbers. Both are Hydr roller with the correct cam pin length for the OPTI, you would be shocked how many OPTI's fail because the cam pin on a new cam was not the correct length:). These are both for blower LT's

1. Manley Titanium exhaust valves, set of 8, 1.625, stock length 11/32 stem with a .290 tip. These will cost you almost $1,200 new but they can be yours for $500
2. G-Force racing jacket. 3-2A/5 rating, large' black with velcro collar and s white strips on the sleeves. You can see how new this is by how white the strips are. $75
Comp Cams Custom Hydr Roller -- Lift = 541/541, Dur. at .050 = 246/258, Lobe sep. = 114 $200 ---- SOLD
Comp Cams Custom Hydr Roller -- Lift = 580/609, Dur. at .050 = 248/258, Lobe sep. = 116 $200 ---- SOLD
Manley Titanium 10 degree valve locks for 11/32 valve - $75
885-16 Comp cam hydr lifters - $300
15855-16 Comp Cam hydr lifters short travel - $300
NOS Bottle Blanket like new -- $25
NOS replacement heater element -- $50
NOS quick release bottle brackets, black -- $70
Crane Gold ultra roller rockers for 7/16 studs non self aligning . Complete set of 1.6 ratio with locks $160. Also 8 Crane Gold 1.5 ratio-- $10 each
Ford 9" US gear 3:89 ratio like new -- $100
10-012 Hays certified 153 tooth gold flex plate -- $40
8252 MSD Blaster coil $70
Nano Nitrous system. Tank, bottle brackets and instructions. $300
New GM LT1 timing chain = $30
Custom LT1 cam timing gear for conversion to electric water pump. Gear has water pump drive gear milled off to save weight. Less stress and quicker revs. $100
Custom 10 rib blower pulley for crank. 7 1/4" dia crank pulley. They are all 1 5/8 spaced out from the balancer to the first rib but I can change that spacing if you need something different. Just let me know what you are looking for and could save you a lot of money. $100 each

Hope one or more of these parts saves you some money on your build!!

Mis-spoke on the blower pulleys, they are all 10 rib. I have updated the post.

Still have stuff looking for a new home. I wish I would have paid the prices I'm sell this stuff to you for!!

Are those crane gold's 1.6's?
How much run time is on them and do you have 16 of them?

Quote:

---

Originally Posted by sic96

Are those crane gold's 1.6's?
How much run time is on them and do you have 16 of them?

---

Sorry for the slow response, I'm not on here that much.

I only have 8 of the Crane gold and they are 1.5's. The red Sharps are 1.6 and I have 14 of those. If you want 8 or more I will make you a deal better than the price posted.

Thanks and hope you can use them.

PM sent


Sent from my iPad using Tapatalk

Sharpe red 1.6 rockers are gone.

But while looking for some ARP rocker studs I found another set of Crane Gold race rockers. 1.6 ratio and 7/16 stud. Also have 8 Crane Gold race 1.5 ratio with 7/16 stud. And a set of ARP 7/16 screw in studs.

All need new homes and you can save a ton of money over buying new. Prices in the original post.

One cam maybe gone also. The comment that was made by the person looking at it was "he couldn't find any cams with numbers like these unless they were for an LS". These are custom grinds, one of a kind made just for me so you will not find anything like them. They have a small base circle for up to a 4" stroke and have lobe profiles you will not find on what you can buy. Really trick cams but only if you are running a supercharger.

One more new item added. Manley 10 degree titanium valve locks for 11/32 stems.

Both cams are now gone.

Still a lot of good stuff that's cheap for you.

Happen to have a part number and pics of the nano kit?