RealQuick
10-29-2011, 08:28 AM
495hp 491ft/lbs @ 7psi thru an AUTO (A/F-11.8-12.0, timing only @ 17 degrees)
600rwhp/605rwtq @ 10psi thru an AUTO (A/F-?, timing @ 21 degrees)
LT1Boost Header Kit (stainless)
1.75" headers
3.5" DP
TC78 .96 A/r
40mm JGS Wastegate
60mm JGS BOV
4" A2A IC
3" cold side
355ci
230cc Brodix LT1 Cylinder Heads w/62cc Chambers
Fully CNC ported intake/exhaust/combustion chambers
Cometic "MLS" Head Gaskets
ARP Undercut Head and Main Studs
CP Pistons & Pins - 24cc Dish (Approx. 9.0:1 comp ratio with 62cc heads and .040 gasket)
Total Seal Piston Rings
Manley 5.700" H-Beam Connecting Rods
Callies Billet Steel Splayed 4 Bolt Main Bearing Caps
Callies "Stealth" 4340 3.75" Stroke Crankshaft - Internally Balanced
Fluidampr 7.5 o.d. internal balance 740101
Cloyes Double Roller Timing Chain
Canton Road Race Oil Pan, Melling High Volume (10%) Pump Mel-10552, and Canton Pickup
Trickflow 7.3" Chromemoly One Piece Pushrods TFS-21407300
224/224 .577/.582 114 LSA
monoblade throttle body with the LT1 style IAC and TPS sensors. I have a 3 bar MAP sensor.
adjustable fuel pressure regulator set to about 42 psi at idle. Twin in-tank walbro 255lph fuel pumps, one set to come on at about 5-6 psi. Fuel injectors are Siemen Deka 80lb high impedance injectors.
Ignition is a LSI PCM with D585 truck coils (lower dwell time) and MSD wires with iridium spark plugs gapped at .031"
Rockers are crower 1.65.
Springs are Comp 26094-16. Seat load: 178lbs @1.900''_Open load: 459lbs @1.275_Rate: 449lbs/in
I'm using LS7 lifter with about .00416" preload.
Fans are Flex Lite 410's.
Tranny is a built 4L60E with a 2800 stall.
Rear end is a 12 bolt with 4.11 gears.
Compression ratio should be around 9.2:1.
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/package.jpg
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/hotparts2.jpg
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/IMG00134-20101219-1653.jpg
600rwhp/605rwtq @ 10psi thru an AUTO (A/F-?, timing @ 21 degrees)
LT1Boost Header Kit (stainless)
1.75" headers
3.5" DP
TC78 .96 A/r
40mm JGS Wastegate
60mm JGS BOV
4" A2A IC
3" cold side
355ci
230cc Brodix LT1 Cylinder Heads w/62cc Chambers
Fully CNC ported intake/exhaust/combustion chambers
Cometic "MLS" Head Gaskets
ARP Undercut Head and Main Studs
CP Pistons & Pins - 24cc Dish (Approx. 9.0:1 comp ratio with 62cc heads and .040 gasket)
Total Seal Piston Rings
Manley 5.700" H-Beam Connecting Rods
Callies Billet Steel Splayed 4 Bolt Main Bearing Caps
Callies "Stealth" 4340 3.75" Stroke Crankshaft - Internally Balanced
Fluidampr 7.5 o.d. internal balance 740101
Cloyes Double Roller Timing Chain
Canton Road Race Oil Pan, Melling High Volume (10%) Pump Mel-10552, and Canton Pickup
Trickflow 7.3" Chromemoly One Piece Pushrods TFS-21407300
224/224 .577/.582 114 LSA
monoblade throttle body with the LT1 style IAC and TPS sensors. I have a 3 bar MAP sensor.
adjustable fuel pressure regulator set to about 42 psi at idle. Twin in-tank walbro 255lph fuel pumps, one set to come on at about 5-6 psi. Fuel injectors are Siemen Deka 80lb high impedance injectors.
Ignition is a LSI PCM with D585 truck coils (lower dwell time) and MSD wires with iridium spark plugs gapped at .031"
Rockers are crower 1.65.
Springs are Comp 26094-16. Seat load: 178lbs @1.900''_Open load: 459lbs @1.275_Rate: 449lbs/in
I'm using LS7 lifter with about .00416" preload.
Fans are Flex Lite 410's.
Tranny is a built 4L60E with a 2800 stall.
Rear end is a 12 bolt with 4.11 gears.
Compression ratio should be around 9.2:1.
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/package.jpg
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/hotparts2.jpg
http://i45.photobucket.com/albums/f94/RealQuick/LT4%20power/IMG00134-20101219-1653.jpg