View Full Version : No rev past 2500
lt1nova
07-17-2011, 12:19 PM
I have developed an problem where I cannot rev past 2500. However this does not happen right away, when it does I've had luck disconnecting the battery to make the problem go away temporarily.
The problem started when I was at a stop sign, loaded the convertor and then took off. The following day I drove to the dragstrip (60 miles) without issue. On the launch of my second run it acted up. I disconnected the battery, got in a run awaited about 40 mins, got in another. I tried to hot lap it and it acted up again. The drive home the next day was fine.
I drove it yesterday about 3 miles one way and it worked fine revved up to 4500, on the return trip it acted up. This morning it ran fine on my drive for the first 5 minutes (once going past 5000) then it acted up again.
I am going to try to attach a datamaster file of this mornings drive. It started acting up around #4250.
Any help would be appreciated.
7416
95ImpySS
07-17-2011, 11:15 PM
Curious, will it rev up in neutral after the problem occurs? Is your Check Engine Light on? Can you tell if it is a problem when your car enters closed loop? Data Master should tell you when your in closed loop. Also, does the car pop and back fire when its having problems going above 2500RPM?
lt1nova
07-20-2011, 11:29 PM
Yes it will it in neutral, well park actually. No the light is not on. I know it does it in closed loop, not sure about open but I think so as I've shut it off, checked somethings, started it and tried to rev and it did it, I don't know how quick it can go into closed loop. Yes it does pop/backfire when trying to rev past.
Formula 350
07-21-2011, 12:21 AM
Ill not sure but it sounds like you may be having a problem with your throttle position sensor
lt1nova
07-24-2011, 03:16 PM
I don't think it is the TPS as I looked at that info on the datamaster and it seemed to be responding fine.
Yesterday I disconnected the battery for a while, today I drove it about 40 miles without going over 2500, ran it up to about 3000 the parked it for ten minutes. When I when to drive it again it was missing again. I was thinking it was ignition related but that doesn't make sense if a disconnect fixes it temporarily. A friend suggested a limp home mode but I am not getting any codes to suggest that.
lt1nova
08-29-2011, 08:58 PM
I am posting a much longer file than I had before. I didn't want to post something non relevant but I guess it may help. After looking at it a bit more I see that I was able to make it over 2500 a few times in closed loop.
Rec #'s around 1410, 1910 & 3075 show over 2500 with only 1410 being in open loop. around Rec #4300 is where it starts acting up. See screenshots or download the whole file.
Datamaster 7/17 long file (http://www.mediafire.com/?cx1dz38sl5s36t6)
http://img5.mediafire.com/46480b9ea9a0a813b1cb2862fcb71a73c69f19654e627fea42 4e422953ff13005g.jpg
http://www.mediafire.com/imgbnc.php/8fa3152e052851e60cd561e772260490272d1f5ae046a6a13c df6550b8c6d3f05g.jpg
http://www.mediafire.com/imgbnc.php/c0f2111edb32e70ac28c1636b49f1910897cafd00c212ebaa8 4618b73ca6a0c75g.jpg
http://www.mediafire.com/imgbnc.php/28710b25f7090b9e038ba0be26ee915e99b6ad16372281fc1b cfcc79c59887965g.jpg
firebird_1995
08-30-2011, 10:46 PM
whats the deal with the vss dtc? sensor not hooked up or something?
lt1nova
09-02-2011, 09:38 PM
It's the output to the speedometer. It's a transplant, the car has a Dakota Digital speedo in it so it may not like that. I've had that code for years.
lt1nova
05-05-2012, 10:53 AM
Guys,
Sorry for bringing up a dead post but I thought I'd let everyone know that I figured out the issue last night after 11 months. I had said it was running like it was on a rev limiter and it was. My MSD Digital 6 is acting up. I put a light up spark tester on a plug wire and could see the spark die around 2500 so I put it on the coil wire. Same issue so I knew it wasn't the opti. I set the rev limter to 1500 and the problem followed. I set it to 9500 and it now rev's past 5k. I'm getting a little breaking up around 15-2000 so I cranked up the two step also but haven't retested. It will be going back to MSD at some point to get checked out.
Thanks to everyone for their input, it's much appreciated.
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.