Become a ltxtech.com member, Click here to register!
BP-Automotive

Results 1 to 9 of 9
  1. #1
    Lurker


    Status
    Offline
    Join Date
    Jan 2019
    Name
    Carl Zachary Decker
    Vehicle
    1996 Chevy Corvette LT1
    Location
    NC
    Posts
    5

    Default 96 LT1 crank no start issue

    Have a 96 LT1, motor was running while testing the tune and just died. Key on fuel pump primes, have good pressure, cranks but will not start. Have no spark at coil. Performed check of ICM harness and have all but 1-4 volts while cranking at terminal B. Performed Opti harness checks and all were good. Performed Fleet service manual checks for PCM, saying I have bad PCM. Snap On scanner communicates with PCM, shows TPS volts and %, Map, etc. But no RPMs when cranking. Question is do I have a bad Opti or bad PCM from tuning/shipping.

  2. #2
    LTX Master


    Status
    Offline
    Join Date
    Aug 2013
    Name
    JB
    Vehicle
    1994 Camaro Z28 1996 Camaro SS
    Location
    Atoka,TN
    Posts
    531

    Default

    Have you checked to see if your rotor spun off?

    Sent from my SM-G955U using Tapatalk
    Same as everybody else...350 small block, double hump heads, 3/4 cam

  3. #3
    Lurker


    Status
    Offline
    Join Date
    Jan 2019
    Name
    Carl Zachary Decker
    Vehicle
    1996 Chevy Corvette LT1
    Location
    NC
    Posts
    5

    Default

    Have not broke into Opti yet. Was hoping to narrow it down a bit more if possible.

  4. #4
    LTx Guru


    Status
    Offline
    Join Date
    Apr 2013
    Name
    Fred
    Vehicle
    1994 Formula - SOLD
    Location
    Central NJ
    Posts
    2,279

    Default

    Do you have spark at all the plugs?

    Do you have fuel pressure?

    Do you have a noid light to verify the injectors are pulsing?

    Have you verified the Opti signals are present, by checking for the pulse on the white wire to the ICM?

    http://shbox.com/1/4th_gen_tech2.html#opti_test

    Is the SECURITY light on while cranking?
    SOLD - GONE TO A (VERY) GOOD HOME ! - 94 Formula A3+1: 381ci forged stroker - Callies Stealth, Oliver 5.85 billet rods, BME nitrous pistons / CNC LT4 heads / CC solid roller / TH400+GearVendors OD / 4.11 Strange 12-bolt / 300-shot N2O / Spohn Suspension / roll bar / MoTeC M48 Pro engine management system /a few other odds 'n ends.

  5. #5
    Lurker


    Status
    Offline
    Join Date
    Jan 2019
    Name
    Carl Zachary Decker
    Vehicle
    1996 Chevy Corvette LT1
    Location
    NC
    Posts
    5

    Default

    No spark at coil or plugs

    Fuel pressure KOEO is 44psi and holds steady

    No test on injector pulse yet

    Followed all steps on shbox.com write up and all checked good except for ICM white wire have no voltage when cranking

    Security light comes on key in but goes off and does not come on when cranking

    I appreciate all helping out.

  6. #6
    LTx Guru


    Status
    Offline
    Join Date
    Apr 2013
    Name
    Fred
    Vehicle
    1994 Formula - SOLD
    Location
    Central NJ
    Posts
    2,279

    Default

    And you got 5 volts on pins A and B in the Opti harness?

  7. #7
    Lurker


    Status
    Offline
    Join Date
    Jan 2019
    Name
    Carl Zachary Decker
    Vehicle
    1996 Chevy Corvette LT1
    Location
    NC
    Posts
    5

    Default

    Yes with harness disconnected from Opti and key on got 5 volts on pins A and B.

  8. #8
    LTx Guru


    Status
    Offline
    Join Date
    Apr 2013
    Name
    Fred
    Vehicle
    1994 Formula - SOLD
    Location
    Central NJ
    Posts
    2,279

    Default

    Lack of the ignition pulse to the ICM can be the result of no low resolution pulse from the optical cam position sensor in the Opti. When the PCM doesn’t see the low res pulse it shuts down the fuel system. There’s a code for a missing low res pulse, but it can’t set unless the PCM also sees the high resolution pulse. The code for the low res pulse will set while the engine is cranking, if the high res pulse is present, and you crank the engine for a longer than normal length of time. That code does NOT turn on the SES light. Have you scanned it for codes?

    When the engine is cranking, does the tach needle move off the stop, up to 200-300 RPM? That is another indication the PCM is receiving the signal from the Opti.

    Another check is to reconnect the Opti, and connect the volt meter to the red/black wire on pin A (+) and the pink/black wire on pin D (-). Key on, slowly rotate the engine. For each revolution of the crank, the Opti low res signal should pull the 5 volts down to ~0 volts four times. You can do the same with the high res wire, measuring from the purple/white wire on pin B to the pink/black wire. But that wire should have 180 5 volt / 0 volt switches per crank rev. Plus, the PCM does not need the high res signal to run the engine. It just improves the timing of the spark and injectors to reduce spark scatter.

    http://shbox.com/1/1996_ec_03_ign_system.jpg

  9. #9
    Lurker


    Status
    Offline
    Join Date
    Jan 2019
    Name
    Carl Zachary Decker
    Vehicle
    1996 Chevy Corvette LT1
    Location
    NC
    Posts
    5

    Default

    shbox gave me another tip to take a spare Opti, connect it to harness, turn key on, with meter hooked to ICM pin B spin Opti and check for 1.4 volts. Got almost 4 volts along with spark from coil and injector pulse. Appreciate all the help. Now time to change Opti.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •