- Navigation
Results 1 to 7 of 7
-
05-28-2017, 08:37 PM #1Xtreme Member
- Status
- Offline
- Join Date
- Apr 2012
- Name
- Mike
- Vehicle
- 96 Z28, 95 Roadmaster
- Location
- Conshohocken, PA
- Posts
- 1,862
Garage Cleanout: computers, exhaust, suspension, performance, stock, etc.
Garage cleanout of some stuff my friend and I aren't using. We need money for more car parts!!! Stuff is split between Conshohocken, PA and Reading, PA if interested in pickup.
Moroso CAI (tube, plate, filter)
Washable filter but the rubber inlet end is cracking
I've been using it for years without issue though
Could be repaired with RTV or replaced (Moroso and K&N make replacements)
$100 shipped
94-95 OBD1 pcm for F, B, and D bodies, p/n 16188051
Can be reflashed with a stock tune by request
Comes with b-body knock module
$75 shipped 1 avail
96-97 OBD2 pcm for F, B, and D bodies, p/n 16214399
Comes with b-body knock module
Sold
2-bolt engine block, needs to be bored b/c surface rust
$150, no shipping
K1 Technologies 6.0" I-beam SBC/LT1 rods
New but opened packages
4340 forged steel
ARP 2000 bolts
Pressed pins (can be bushed by machine shop if desired)
$230 shipped or trade for 6.125 rods
ARP rod bolts for stock rods, new but opened package
2 missing from new package but comes with several spares (but most need threads chased)
$40 shipped
Factory Z28 sway bars
$25 for the pair, no shipping
SLP triangulated subframe connectors
Great for autox/road racing, very rare, missing hardware though
Sold
Pioneer billet keyed hub, used with some surface rust
$40 shipped
Borla Catback, in good shape
$300, no shipping
One Yukon axle for B-body, narrow type (non B4U caprice, roadmaster, fleetwood), used
$80 + paypal and shipping
2.56 B-body 8.5" 10 bolt gears, used 100k, no noise
$30 + paypal and shipping
Auburn G80 posi from in good shape from 8.5" 10 bolt B-body, 100k, from 2.56 car
Pin and bolt are MIA, will look for them
$50 + paypal and shipping
Spline drive timing covers
$20 + paypal and shipping
A1 Cardone reman water pump, new in box
$40 + paypal and shipping
Founders adjustable panhard bar, bolt seized in one end so it needs to be drilled out (or have bushing replaced)
$30 (would prefer not to ship)
Ebay intake elbow, poorly polished
$20 + paypal and shipping
Crown Vic P71 3.5" aluminum driveshaft, has small gouges around 40" mark, good for cutting down or repair
$20 get this out of my garage
Some pics, not everything is shown. PM for more.
0528170220-1.jpg0528170220a-1.jpg0312172135-1.jpg0526171853-1.jpg0529172133.jpg0529172132.jpg0529172125b.jpg0529172125a.jpg0529172120a.jpg0529172120.jpg0529172040.jpg0529172038a.jpg0529172038.jpg0528172230.jpg0526171822.jpgLast edited by Catmaigne; 07-10-2017 at 09:15 AM.
96Z M6, ERE-383 #60, AFR 210s, LE cam, 9", Procharger D1, ???whp
95 Roadmaster T-56 swap, LE1s, baby cam, 4.56s, "The Cammaster"
95 Firehawk hooptie, bolt-ons and suspension
-
-
05-28-2017, 08:43 PM #2Xtreme Member
- Status
- Offline
- Join Date
- Nov 2012
- Name
- Shaun
- Vehicle
- 1994 Formula
- Location
- Phillipsburg NJ
- Posts
- 7,249
Supporting Member2021 Charger Scat 392
1994 Firebird Formula 381 stroker - Carrying the torch! - 9.90 @ 134.3mph on a 200 shot
The wrench/driver for LTConvert's 94 Z28- Ellwein 383/LE Trickflows/ D1SC / CPT Ultra Pro Race 4L60E
10.78 @ 125mph. Shooting for 9.99 for Frank Cahall!
-
05-30-2017, 08:50 AM #3Xtreme Member
- Status
- Offline
- Join Date
- Apr 2012
- Name
- Mike
- Vehicle
- 96 Z28, 95 Roadmaster
- Location
- Conshohocken, PA
- Posts
- 1,862
Bump, pics added
Sent from my VS986 using Tapatalk96Z M6, ERE-383 #60, AFR 210s, LE cam, 9", Procharger D1, ???whp
95 Roadmaster T-56 swap, LE1s, baby cam, 4.56s, "The Cammaster"
95 Firehawk hooptie, bolt-ons and suspension
-
The Following User Says Thank You to Catmaigne For This Post:
-
06-02-2017, 06:58 AM #4Xtreme Member
- Status
- Offline
- Join Date
- Apr 2012
- Name
- Mike
- Vehicle
- 96 Z28, 95 Roadmaster
- Location
- Conshohocken, PA
- Posts
- 1,862
Computers are sold, subframe connectors are tentatively sold
Sent from my VS986 using Tapatalk96Z M6, ERE-383 #60, AFR 210s, LE cam, 9", Procharger D1, ???whp
95 Roadmaster T-56 swap, LE1s, baby cam, 4.56s, "The Cammaster"
95 Firehawk hooptie, bolt-ons and suspension
-
The Following User Says Thank You to Catmaigne For This Post:
-
06-07-2017, 07:10 AM #5Xtreme Member
- Status
- Offline
- Join Date
- Apr 2012
- Name
- Mike
- Vehicle
- 96 Z28, 95 Roadmaster
- Location
- Conshohocken, PA
- Posts
- 1,862
Bump, 1 pcm and forged rods added
Sent from my VS986 using TapatalkLast edited by Catmaigne; 06-07-2017 at 07:18 AM.
96Z M6, ERE-383 #60, AFR 210s, LE cam, 9", Procharger D1, ???whp
95 Roadmaster T-56 swap, LE1s, baby cam, 4.56s, "The Cammaster"
95 Firehawk hooptie, bolt-ons and suspension
-
The Following User Says Thank You to Catmaigne For This Post:
-
07-10-2017, 09:15 AM #6Xtreme Member
- Status
- Offline
- Join Date
- Apr 2012
- Name
- Mike
- Vehicle
- 96 Z28, 95 Roadmaster
- Location
- Conshohocken, PA
- Posts
- 1,862
Bump, still have lots of stuff
Would also be willing to trade for 6.125 rods (although unlikely)96Z M6, ERE-383 #60, AFR 210s, LE cam, 9", Procharger D1, ???whp
95 Roadmaster T-56 swap, LE1s, baby cam, 4.56s, "The Cammaster"
95 Firehawk hooptie, bolt-ons and suspension
-
06-01-2020, 01:46 PM #7
Do you still have a ‘94-‘95 PCM for an LT1?
Let me know what you're asking plus shipping to Missouri Zip code 64093
Thanks!
Ben Smith
Bookmarks