- Navigation
Results 11 to 20 of 30
-
01-12-2017, 07:59 AM #11
Problem 1. Car ran for 3 mins then died and now it only cranks.
Solution 1. As already stated check fuel pressure then report back.
Problem 2. No tools
Solution 2. Rent tools at local Auto Parts Store to test fuel pressure.
Post up what you find out and Good Luck!355 LT1 Turbo, Ported TFS heads, LE Ported Intake, LE cam, 80lb inj, Dual pumps 340 & 320lph on e85, etc.....
www.fquick.com/SleepyZ
-
The Following User Says Thank You to sleepy_z For This Post:
-
01-12-2017, 09:48 AM #12InActive Member
- Status
- Offline
- Join Date
- Jan 2017
- Name
- tray stinson
- Vehicle
- 1995 roadmaster sedan
- Posts
- 15
Got you
-
01-12-2017, 11:35 AM #13InActive Member
- Status
- Offline
- Join Date
- Jan 2017
- Name
- tray stinson
- Vehicle
- 1995 roadmaster sedan
- Posts
- 15
Dont have money right now to get pressure checker. But I smell gas iut the pipe and see sime exhaust. But my a and d terminals on my icm harness has no volt.
-
01-12-2017, 12:04 PM #14
Last edited by atlantadan; 01-12-2017 at 12:06 PM.
-
01-12-2017, 12:08 PM #15InActive Member
- Status
- Offline
- Join Date
- Jan 2017
- Name
- tray stinson
- Vehicle
- 1995 roadmaster sedan
- Posts
- 15
O ok ciol
-
01-12-2017, 12:09 PM #16InActive Member
- Status
- Offline
- Join Date
- Jan 2017
- Name
- tray stinson
- Vehicle
- 1995 roadmaster sedan
- Posts
- 15
How do u check the coil
-
01-12-2017, 12:59 PM #17
Last edited by atlantadan; 01-12-2017 at 01:05 PM.
-
01-12-2017, 01:14 PM #18Xtreme Member
- Status
- Offline
- Join Date
- Nov 2012
- Name
- Shaun
- Vehicle
- 1994 Formula
- Location
- Phillipsburg NJ
- Posts
- 7,266
Supporting Member2021 Charger Scat 392
1994 Firebird Formula 381 stroker - Carrying the torch! - 9.90 @ 134.3mph on a 200 shot
The wrench/driver for LTConvert's 94 Z28- Ellwein 383/LE Trickflows/ D1SC / CPT Ultra Pro Race 4L60E
10.78 @ 125mph. Shooting for 9.99 for Frank Cahall!
-
01-12-2017, 01:44 PM #19InActive Member
- Status
- Offline
- Join Date
- Jan 2017
- Name
- tray stinson
- Vehicle
- 1995 roadmaster sedan
- Posts
- 15
Ok checjed a and d terminal on harness going to icm I have no volts coming from a and d. I do for b and c though. Put car in diognostic mode.
And agot codes under 03.... they were 61 62 161 and 162Last edited by bigontray; 01-12-2017 at 03:55 PM. Reason: wrong nunber
-
01-12-2017, 04:35 PM #20LTx Guru
- Status
- Offline
- Join Date
- Apr 2013
- Name
- Fred
- Vehicle
- 1994 Formula - SOLD
- Location
- Central NJ
- Posts
- 2,283
On the ICM, pins A and D are 12V DC, supplied by a fuse. Check the fuse. On an F-Body it's under the hood... don't know about the B-Body.
Pin C is a ground. It should not have any voltage on it (if you put one lead of the meter on pin C, where did you put the other lead?). Measure ohms from pin B to a good ground. Should read close to "0" (key off).
Pin B is the pulse signal from the PCM that tells the ICM to fire the coil. Did you measure it with the engine cranking? You have to measure that with the AC Volts scale. What value did you get?
http://shbox.com/1/4th_gen_tech2.html#opti_test
What year PCM are you using? 2-digit codes would appear to be OBD-1. OBD-2 are 3- and 4-digit codes.
How did you put the PCM in diagnostic mode? What scanner did you use? DTC 61 is for the A/C system, there is no DTC 62 for an F-Body, is there one for a B-Body?Last edited by Injuneer; 01-12-2017 at 04:42 PM.
SOLD - GONE TO A (VERY) GOOD HOME ! - 94 Formula A3+1: 381ci forged stroker - Callies Stealth, Oliver 5.85 billet rods, BME nitrous pistons / CNC LT4 heads / CC solid roller / TH400+GearVendors OD / 4.11 Strange 12-bolt / 300-shot N2O / Spohn Suspension / roll bar / MoTeC M48 Pro engine management system /a few other odds 'n ends.
Bookmarks