- Navigation
Results 1 to 6 of 6
Thread: MWC Fab9 brake line routing ??
-
04-09-2014, 08:03 PM #1Lurker
- Status
- Offline
- Join Date
- Oct 2012
- Name
- Charlie DeBolt
- Vehicle
- 1995 Camaro Z28 Black M6 Ttops
- Location
- South East, Michigan
- Posts
- 36
MWC Fab9 brake line routing ??
Anyone have pics of brake line routing on a MWC Fab9 with LT1 brakes?
1995 Z28 M6 LT1 Black
-
04-09-2014, 08:16 PM #2VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
@96LT1355Z28
maybe josh can help you... don't know what your having issues with.. run some 3/16 hard line along the housing, buy a couple braided lines to connect each caliper and depending on if your a 4 or 3 channel car you will need one or 2 braided lines to connect to your factory hard lines that are on the drivers side by the center section...
-
04-09-2014, 08:29 PM #3Lurker
- Status
- Offline
- Join Date
- Oct 2012
- Name
- Charlie DeBolt
- Vehicle
- 1995 Camaro Z28 Black M6 Ttops
- Location
- South East, Michigan
- Posts
- 36
Well I was wanting to reuse the existing lines is possible.
No real issues yet. Just getting ready to install and looking for pics that reused the original lines.Last edited by Z28-50; 04-09-2014 at 08:43 PM.
1995 Z28 M6 LT1 Black
-
04-09-2014, 08:55 PM #4VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
Don't think your going to re use stock lines, maybe if you bent them.around the center of the housing but I think you'll be short.
-
04-10-2014, 10:17 AM #510 Second N/A Club
- Status
- Offline
- Join Date
- Sep 2008
- Name
- Josh
- Vehicle
- 96 Z28
- Location
- Holden, MO (KC)
- Posts
- 2,867
I reused my stock steel lines back in 2007 cause I was completely out of $! I've since had the rear end shortened so the rubber hoses at the ends are probably flexed more than they're supposed to be but I've learned to not mess with it if it works with this car! It's pretty crude lookin but hey it's not a show car right! Here's some pics please ignore the dirt/dust. I replaced several sections of sheet rock in my garage and the car was inside for half and outside in the rain for the other half.
DS BK.JPGPS BK.JPGDS FRT.JPGPS FRT.JPG-Josh
co-owner of BDBRacing.com
NMCA OC 9004
96, N/A 385, Holley EFI, Faceplated M6, AI TFS heads, LE SR cam, MWC Fab 9
10.16 @ 136 1.50 60'........still workin on that 60' shootin for 1.4's!
-
04-10-2014, 11:14 AM #6Lurker
- Status
- Offline
- Join Date
- Oct 2012
- Name
- Charlie DeBolt
- Vehicle
- 1995 Camaro Z28 Black M6 Ttops
- Location
- South East, Michigan
- Posts
- 36
Thank you Josh and Kyle.
Charlie1995 Z28 M6 LT1 Black
Bookmarks