- Navigation
Results 21 to 30 of 848
Thread: project Gramps
-
11-01-2013, 11:19 AM #21VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
-
The Following User Says Thank You to dawdaw For This Post:
-
11-01-2013, 11:35 AM #22Lurker
- Status
- Offline
- Join Date
- Dec 2012
- Name
- Tommy N.
- Vehicle
- Silver 1996 Camaro Z28, Green 1996 Camaro Z28
- Location
- El Paso, TX
- Posts
- 946
@dawdaw what brakes are those they look weird to me and that's a lot of work for that short of time frame
Silver 96 Z28 SideSwype-DD
Green 96 Z28 NightMare-Drag car96 Camaro Z28 Silver Mostly Stock, Full Exhaust
96 Camaro Z28 Green Big Cam, Quick Performance 9 Inch Rear End, Full Exhuast
-
11-01-2013, 12:00 PM #23VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
They are strange brakes
http://www.strangeengineering.net/catalog/
Look on bottom left it'll say pro race brakes, they are hub mounted not the Anglia spindle mount style.
-
The Following User Says Thank You to dawdaw For This Post:
-
11-14-2013, 07:23 PM #24VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
Well called up MWC the other day, had a few other things added to the rear end that might make it have a little less resistance and put a different case in it
-
11-27-2013, 05:52 PM #25VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
Well the rear is gone, got me a couple rods i have to throw in this winter.. was shaking a little last season
Which center section do you guys like the most???
-
11-27-2013, 06:45 PM #26
Da faq kinda rods are they?
Correlation does not imply causation.
Una salus victis nullam sperare salutem
-
11-27-2013, 06:48 PM #27VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
there out of a 24 valve cummins... how do you think they make all there torque? just got to run a thick wrist pin to match the pistons and some thick bearings
-
11-27-2013, 06:49 PM #28
Ew, 24v
Correlation does not imply causation.
Una salus victis nullam sperare salutem
-
11-27-2013, 06:50 PM #29Xtreme Member
- Status
- Offline
- Join Date
- Dec 2011
- Name
- JeremY
- Vehicle
- 1972 NovA
- Location
- Elsberry, MO
- Posts
- 4,416
I like the one on the right!
'72 Nova "HadeSS"
-
11-27-2013, 06:58 PM #30VIP Member
- Status
- Offline
- Join Date
- Apr 2011
- Name
- KYLE
- Vehicle
- 95 MQBM Z28
- Location
- davison michigan
- Posts
- 3,874
LOL those rods were out of like a 1900 horse naturally aspirated big block pro stock engine... they have to pitch them away after so many cycles of stretching and they get worn out fast. Picked a few of them up for 10 bucks at an ADRL RACE and i tell people there out of my car and they think im serious
well hell ya, i ordered that one! Strange ultra case baby! with some gun drilled, pocket milled 40 spline axles, 3.812 case, large stem gear, micro blued bearings!!! got to look forward to an x275 build in a couple years
-
The Following User Says Thank You to dawdaw For This Post:
Bookmarks