Become a ltxtech.com member, Click here to register!
CPT

  • Navigation

Search:

Type: Posts; User: 93bird

Page 1 of 3 1 2 3

Search: Search took 0.34 seconds; generated 4 minute(s) ago.

  1. Replies
    5
    Views
    16,452

    My car is not lowered. I have 255/50/16 toyo...

    My car is not lowered. I have 255/50/16 toyo proxes tq drag radials on it now and I have 3-4 inches between the top of the tire and the wheel lip of the quarter I also have about 2 1/2 inches between...
  2. Replies
    5
    Views
    16,452

    Nitto NT05R 315/40R18

    Nitto Nt05r 315/40r18. Anyone running these on a 4th gen. How do they fit, will a 18x10.5 wheel with a 56. offset and 7.95 back space fit or will I need spacers. Got a smoking deal ( $438 ) on a pair...
  3. Replies
    5
    Views
    7,929

    The cover I have now is a 95. I will have to dig...

    The cover I have now is a 95. I will have to dig thru my paper work to see the part# on the set I used. I wrnt to switch to the 96-97 cover so I can run the 411 pcm.
  4. Replies
    5
    Views
    7,929

    You can't clearance it like the 92-95 covers. I...

    You can't clearance it like the 92-95 covers. I have one on my 95 setup with a facktory cover that I clearance with a grinder
  5. Replies
    5
    Views
    7,929

    cloyes double row timing set on 96-97 lt1

    will it work with the reluctor wheel?
  6. Thread: Bad opti ????

    by 93bird
    Replies
    1
    Views
    8,139

    Bad opti ????

    I havn't been on the forum in a few years, totaled my 93 formula almost two years ago. It had a fresh 383 ( less than 3000 miles ) and a new 9inch rear end. I let the car sit for a year and a half....
  7. The opening of the main pipe is 2.75 then it...

    The opening of the main pipe is 2.75 then it opens to 3" and then 2.5" when it splits into two pipes over the rear. I think its smaller to tie in to the stock exhaust pipe.
  8. I had one on my formula for 3 years, first with...

    I had one on my formula for 3 years, first with stock manifolds (sounded good) then with ebay stainless headers & y-pipe (sounded awesome). The only reason I got rid of it was when I replaced my rear...
  9. I just installed a QP 9" in mine. I do plan on a...

    I just installed a QP 9" in mine. I do plan on a good bit of track time next year with some hoosier drag radials.
  10. how much horsepower can a stock steel vs stock aluminum drive shaft take

    My new motor is 525ish. fly wheel HP. will either hold up
  11. A4 CARS what gear do you go thru the traps in an A4 car

    like it says what gear are you in going thru the traps
  12. Replies
    4
    Views
    731

    qoick performance 9inch

    I'm in the market for a 9inch rear end housing and I'm looking at the quick performance 9inch, anyone running one what do you think of the quality..
  13. Thread: valve covers

    by 93bird
    Replies
    28
    Views
    2,252

    I have a pair of the ebay valve covers on my 383...

    I have a pair of the ebay valve covers on my 383 with the comp pro mags with 608 lift no clearance or leaking problems
  14. Push rods were wrong, "to short", Thanks...

    Push rods were wrong, "to short", Thanks...
  15. how far down are they

    how far down are they
  16. ? about comp cams pro magnum roller rockers and poly locks

    For anyone that runs them, when you adjust the valves and remove the slack from the push rods then one more turn then tighten the set screw how much of the set screw sticks out of the nut. I have...
  17. Thread: Quench ?

    by 93bird
    Replies
    10
    Views
    1,375

    Scat forged 383 crank, scat 6in forged procomp I...

    Scat forged 383 crank, scat 6in forged procomp I beam rods, mahle forged pistons rings file fit for a 300 shot, total engine airflow cam dur 236/248 lift 608/600 on a114, trick flow 205cc runners 62...
  18. Thread: Quench ?

    by 93bird
    Replies
    10
    Views
    1,375

    11.48:1 with the .027 vs 11.2:1 with the .036...

    11.48:1 with the .027 vs 11.2:1 with the .036 gasket
  19. Thread: Quench ?

    by 93bird
    Replies
    10
    Views
    1,375

    So then the .027 gasket would be better than the...

    So then the .027 gasket would be better than the .036?
  20. Thread: Quench ?

    by 93bird
    Replies
    10
    Views
    1,375

    Block has been decked so the pistons are.010 in...

    Block has been decked so the pistons are.010 in the hole, 62cc chambers head gaskets will be .027, or .036
  21. Thread: Quench ?

    by 93bird
    Replies
    10
    Views
    1,375

    Quench ?

    How do I know what my quench is?
  22. Replies
    3
    Views
    661

    comp cams ultra pro magnum rockers

    Will the 1.6 ultra pro mags with 7/16 studs clear stock valve covers or the stock hieght aluminum valve covers on ebay?
  23. Replies
    6
    Views
    634

    The heads are not on, and I don't have head...

    The heads are not on, and I don't have head gaskets yet. I was just wondering if the thiner gaskt would help but it will only raise it to 11.48:1
  24. Replies
    6
    Views
    634

    head gasket/comp ratio help

    Ok so about a month ago I posted the specs for my new 383 nitrous motor with 11.2:1 com ratio, and most of you said it was a bit low. I was wondering if a thiner head gasket would help. T.E.A....
  25. Replies
    4
    Views
    460

    professional products t-body

    Are they any good found a close out $110 for a 58mm
Results 1 to 25 of 65
Page 1 of 3 1 2 3