Do you think your steering shaft clearance is giving you false knock?

Where are you located bud?

Where in MD are you?

Liked and commented.

Ironic. I just got bit by the bug too. I just picked up a Century VZ2008. I haven't take it to the range yet.

Sent from my SCH-I535 using Tapatalk

I've been running aftermarket wheels with the 120mm pattern for a few years without much issue. Like mentioned, you do have to torque the wheels in a slow progression. If you torque one lug before at...

I did think about doing red dip on it, but the hood is too big of an item to do something that doesn't match.

I did dip the hood, but because of the humidity, it turned out like crap. Im going to...

I've calmed down a bit, but I'm still having a hard time wanting to work on the car. For some reason, I have a blast doing brake/suspension work. I did a radiator, water pump, upper and lower hoses,...

So I'm in the middle of doing a cooling system revamp on my Trans Am. The entire time, I've been bitching and cussing and wanting to get rid of the car.

I know part of it is living in an...

Being human is what gives us the opportunity to choose right from wrong. Why is it that people never seem to do so?

That's a good deal for wagon wheels. I bought a set years ago for 250, never did anything with them, and ended up giving them to a friend that was strapped for cash to scrap or sell.

I see it at UPS all the time. This year, there was 3 young guys fired for stealing off of one of the belts. This past week, the supervisor for that belt was fired for stealing. UPS has a nice pension...

Hey guys. I have a 97 T/A in red. I have a ram air hood that has been sitting for close to 3 years now, and a LS1 lid/base I've had for just as long.

At the moment, I don't know a shop that I...

I'm getting ready to put a set of 4.10s in the rear on my T/A. The car has 208k miles on it so it's due for a full rebuild. What are you guys using for rebuild kits? Rockauto has a kit for 75ish...

If getting used arms, I would advice changing the bushings anyways. Moog has a neat Problem Solver bushing for the vertical bushing that I want to try. It uses a spherical design to eliminate binding...

The hose mod is when you remove the thick rubber isolator from the rear spring and slide a section of heater hose over the top coil of the spring. It typically lowers the rear 3/4 of an inch

Sent...

This. I have BMR springs and Konis. I didn't do the hose mod in the rear since I have a sub box, and with a full tank of gas, the rear would sit slightly lower than the front.

Sent from my...

I have the same noise. Only noticed it after I put in my Pro5.0.

Mine has 208k on it, so it's to be expected. My co-worker has a 30k mile t56 swapped into a fox body and his makes the same noise....

Man, that looked textbook!

Reineventing the wheel is how progress is made.

Sent from my SCH-I535 using Tapatalk

I intend to make my own window relay setup. I looked into trying to use transistors or mosfets in place of the relays but I'm not that good at electronics yet.

I use 3157 LED's from Autolumination for the turn signals and had to replace the flashers.

Sent from my SCH-I535 using Tapatalk

http://i112.photobucket.com/albums/n184/Tbird232ci/20140414_164524_zpsa4h5plnt.jpg

Another shot for you. The lights are on, showing how the LED's look.

Maybe one day I'll update my signature.

I wonder who took that pic...hmmmm ;)

All I did was take clear corners I got off of ebay, mask off the DRL section, and use Duplicolor Metalcast orange on the part I wanted amber. I used I think...

Why not do both?

http://i112.photobucket.com/albums/n184/Tbird232ci/1017169_482304978518125_1513651715_n_zpsb08b66e5.jpg