Sorry for the late reply, wasn't able to acces the site for some reason. I haven't been able to say for sure if its fixed, however, I did go under it and repaired 2 ground wires. Small one from the...

Well something is screwed. Started the truck, runs fine, put it in gear, wont move. Shift to park and get a terrible buzzing or high speed grinding from the transfer case area. If i go back to any...

Ill give that a go. Im assuming since i already screwd up alignment last time, theres no real point in marking the shaft again except maybe the yoke up at the trans.

Sent from my SM-G965U using...

I know this may not be the right place to start but i figured a bunch of car guys might be able to help me out here. I replaced my transfer case encoder motor on my 2004 suburban 2500. While i had...

Thank you I will check that. This is the kind of thing I hope it turns out to be, something stupid and cheap or free to fix.

Sent from my SM-G965U using Tapatalk

I briefly read into that yesterday as I was looking for answers why it wasn't connecting. Thank you for the link, very simple and straightforward

Sent from my SM-G965U using Tapatalk

I wish I had known to watch the tach when it wasn't starting. Like I said I went out 15 minutes later and it fired up like nothing happened 2 times in a row so I parked it and left it go. So...

I seem to be having a heat soak problem with my car causing it to shutoff while driving. No check engine light, check gauges pops up though. I had this issue last summer one day, randomly shut off...

Alright so I finally had to fill up for the first time since posting this thread. Remember I said how the pump stopped but still spilled some fuel down the side of the truck? Well I went to the same...

I wish there was some sort of explanations as to what each set of numbers meant. The only thing I could do is contact blue driver and see what they can tell me.

Sent from my SM-G965U using Tapatalk

I have no idea what these numbers means but several of the tests as you can see were not completed indicated by the yellow symbol. The red x marks indicate completed and failed both of which state...

Driving home yesterday it acted up briefly when I had to brake heavy but corrected itself. Same issue where short term O2s went haywire briefly. Another little interesting feature of this scanner I...

Unfortunately I don't think I can go back and see that. I have to actually choose which parameters I want to view in real time. I have been trying to go back and watch the logs I have from the day it...

I hope the issue was with the fuel overflow but those O2s wont be on the truck too much longer anyway. I'm looking into some stainless headers and exhaust and will be replacing all of them when that...

I'll do a little bit of research on it when I get a chance but that would be awesome if that pump caused the issue. Thanks for the input, now I have a good direction to look.

Sent from my SM-G965U...

This weekend didn't go as planned and I wasn't able to clean the grounds or check plugs. I intend in doing that this weekend for sure. Anyways the truck has been running great since I posted this...

The attached pic is some of the grounds under the drivers door that go to the 4wd system and some fuel or engine system. Not 100% exactly which ones yet but people have reported these grounds causing...

I can look into how to pull the files from the blue driver. They are saving to my phone but not playing for me. I sent them via gmail to myself and could not open them either. I'll work on that get...

These are all good ideas I need to look at, wish I had a better way to determine which to start with. I did not test my fuel pressure personally the shop did. However I assume since it wasn't acting...

Sorry I may have used the wrong term but my throttle body has a small hole in it above the blade that I assumed was used to regulate the idle when the blade is closed. It is a drive by wire throttle...

And I always fill up at the same Exxon station with 93 fuel. I did run a small bottle of gumout in one tank prior to the issue seeming to get worse. Ill have to check the plugs and see what they look...

Bought the truck in Oct. Immediately had a new intake manifold and gasket installed due to a code that is escaping my memory now. So the manifold and gasket should be good to go. The first I noticed...

Guys I've had my 6.0 Suburban in the shop multiple times for this random issue that has proven difficult to diagnose. I don't want to keep running in and out of the shop so I need to start digging...

New ignition switch is installed. I couldn't see any sign of damage or burning to it or the connectors so hopefully something internal? I did buy replacement harnesses as well but chose not to cut...

Looking at starters... probably going to hold off on replacing the starter but for future reference, anyone have the ACdelco pn for this corvette gear reduction starter? I found one on summit but it...