Become a ltxtech.com member, Click here to register!
BP-Automotive

  • Navigation

Search:

Type: Posts; User: Ardent_Z28

Page 1 of 9 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    1,773

    Yay, I found them!!...thanks to the link you...

    Yay, I found them!!...thanks to the link you provided Injuneer. I was mistakenly looking for a fusible link the same gauge as the battery cables (like the one on my F150). I had tucked these under a...
  2. Replies
    6
    Views
    1,773

    Well I checked for the fusible link last night...

    Well I checked for the fusible link last night after work as suggested by Injuneer and didn't find one. This morning I decided to check my grounds as my Momma always suggests with total power...
  3. Replies
    6
    Views
    1,773

    Ignition start switch again?

    After putting a few miles on my Z28 following some upgrades and mods, I parked it and shut it off. Immediately turned the key to restart and zilch. No movement of the gauges, no power to the driver...
  4. Replies
    4
    Views
    758

    When I installed my electric water pump, I...

    When I installed my electric water pump, I removed the mechanical pump drive gear and covered the hole with a quarter and some JB weld. I did it from the inside of the front cover, but that should...
  5. Replies
    8
    Views
    15,771

    This is the chart from post #3...39091 My Denso...

    This is the chart from post #3...39091
    My Denso plugs (16) are the equivalent heat range as the NGK plugs (5) Injuneer mentioned. I just got the engine back on the K-member yesterday, still gotta...
  6. Replies
    8
    Views
    15,771

    It is all stock except the cam...Duration @ .050...

    It is all stock except the cam...Duration @ .050 intake is 220 & exhaust is 230 with 114 LSA. Beehive valve springs in the heads, so it is slightly more aggressive than stock. AIR/EGR deleted too.
  7. Replies
    8
    Views
    15,771

    I found the Heat Range Cross Reference Chart in...

    I found the Heat Range Cross Reference Chart in that link which shows the Denso plugs and NGK plugs have the equivalent heat range. Thanks for the information Injuneer...I appreciate it.
  8. Replies
    8
    Views
    15,771

    Spark plug heat range

    I have installed Denso DNP-4713 spark plugs from Summit Racing in my engine, which have a heat range of 16. The AC Delco plugs I removed only have a number 14 on the ceramic. I tried to research if...
  9. Replies
    10
    Views
    6,425

    Those are my sentiments exactly, as well as the...

    Those are my sentiments exactly, as well as the procedure I plan to follow. However, I did learn that if I needed this setup back together quickly then I'll consider Permashield since it has a very...
  10. Replies
    10
    Views
    6,425

    Are you referring to the vacuum ports or the...

    Are you referring to the vacuum ports or the mating surface of the intake and heads? I have FelPro gaskets for the mating surface with the heads I intend to use...that is all the material I cleaned...
  11. Replies
    10
    Views
    6,425

    Recomended intake sealant?

    I finally got around to installing the billet oil pump drive I bought from TubbyFormy 4 years ago and was thinking of using Permatex Ultra Black to seal each end. The sealant I removed was a grey...
  12. Thread: Loan a Tool

    by Ardent_Z28
    Replies
    19
    Views
    63,156

    PM sent.

    PM sent.
  13. I am holding back tears as I post this. My 4L60e...

    I am holding back tears as I post this. My 4L60e is currently in his shop and was getting a Pro Race build Thanksgiving week. It may possibly be his last build. I've been busy dropping my engine &...
  14. Replies
    10
    Views
    9,882

    Alright then...PM'd ya.

    Alright then...PM'd ya.
  15. Replies
    10
    Views
    9,882

    It turns out both of my parts have the groove...

    It turns out both of my parts have the groove etched into them. Since the gasket on the front cover of the LT1 engine is already a source of frustrating oil leaks, I'm gonna opt out of selling them....
  16. Replies
    10
    Views
    9,882

    I believe you're right...I have a rebuild book...

    I believe you're right...I have a rebuild book showing that gear with the same view and no groove present. I have 2 of these so I'll clean up the other one and check it out & get back to ya. Good...
  17. Replies
    10
    Views
    9,882

    39036390373903839039

    39036390373903839039
  18. Replies
    10
    Views
    9,882

    I have a spare water pump drive gear if ya are...

    I have a spare water pump drive gear if ya are still needing one. LMK.
  19. Replies
    1
    Views
    7,615

    Well the morning sunshine revealed it is a failed...

    Well the morning sunshine revealed it is a failed exhaust manifold gasket. Black exhaust soot can be seen on the head, in front of the #1 exhaust port at the header flange. There is no exhaust soot...
  20. Replies
    12
    Views
    11,424

    I am interested. PM sent.

    I am interested. PM sent.
  21. Replies
    1
    Views
    7,615

    #1 exhaust valve blow-by?

    I heard what I thought was a ticking sound coming from #1 cylinder area. I put my hand in front of the valve cover and realized it was a hissing noise, and I felt air pushing it's way out from under...
  22. Replies
    6
    Views
    9,985

    An upgrade I should consider. A radiator flush is...

    An upgrade I should consider. A radiator flush is a cheap diagnostic procedure. I've had a radiator rodded on another vehicle I had but the shop has since closed.
  23. Replies
    6
    Views
    9,985

    Maybe ya pinched or kinked the steam tube between...

    Maybe ya pinched or kinked the steam tube between the heads at the rear of the motor? Even a ding in such a small diameter tube worries me when I think of my upcoming tranny swap.
  24. Replies
    9
    Views
    7,384

    I am interested in the stock bore block. Is...

    I am interested in the stock bore block. Is shipping an option? Which of the pics is that block?
  25. Thread: FOR SALE!!

    by Ardent_Z28
    Replies
    22
    Views
    38,619

    The visors look good...I'd like to have them. Do...

    The visors look good...I'd like to have them. Do ya have a price in mind?
Results 1 to 25 of 207
Page 1 of 9 1 2 3 4